Mini GSM/GPRS + GPS Breakout - SIM808

Overview

This board based on the latest SIMCOM SIM808 GSM/GPS module, it offers cellular GSM and GPRS data along with GPS technology for satellite navigation.

The board features ultra-low power consumption in sleep mode, giving the project incredibly long standby times. Furthermore there's an onboard battery charging circuit that can be used with LiPo batteries.

The GPS receiver is incredibly sensitive with 22 tracking and 66 acquisition channels, and also supports assisted-GPS (A-GPS) for indoor localisation. The board is controlled by AT command via UART and supports 3.3V and 5V logical level. It comes with a mini GPS and GSM antenna, however a battery is optional.

The board uses the 2G (not 3G or LTE) GSM networks.

Features

GPS Specifications

Functional Block

Pin Definitions

Name I/O Description Note
BAT Power input / output 3.4V - 4.4V DC
GND Power ground / logic ground
VIO I Logic level reference 3.0V - 5.0V DC
DTR I Wake up pin for module in sleep mode
PWR O Power switch Low level pulse
RI O Event/ message pin
TXD O Transmit data UART output from SIM808
RXD I Receive data UART Input to SIM808
RST I Module rest

Indicator LEDs

Indicator LEDs Status Behavior
Operating Status (Green) Off SIM808 is not running
On SIM808 is running
Network Status (Red) Off SIM808 is not running
64ms on/ 800ms Off SIM808 not registered to the network
64ms On/ 3000ms Off SIM808 registered to the network
64ms On/ 300ms Off PPP GPRS communication is established

Usage

Related Product

The module comes with a mini GPS and GSM antenna, but not includes Li-Po battery. In addition, to use this module, you still need a unlock SIM-Card that supports GPRS service.

<picture>

<picture>

<picture>

Reference Circuit

Getting Started with AT Command

The module is controlled by AT command via serial port, here we use Arduino as USB to serial tool. Upload the following code to Arduino and open the serial monitor. If you use other USB to serial tools, you can use AT Command Tester or SSCOM32 to test AT commands.

// this sketch is used for testing LoNet with Arduino 

// Connect VIO to +5V
// Connect GND to Ground
// Connect RX (data into SIM808) to Digital 11
// Connect TX (data out from SIM808) to Digital 10

#include <SoftwareSerial.h>

SoftwareSerial mySerial(10, 11); // RX, TX

void setup()  
{
  // Open serial communications and wait for port to open:
  Serial.begin(9600);
  mySerial.begin(9600);

}

void loop() // run over and over
{
  if (mySerial.available())
    Serial.write(mySerial.read());
    
  if (Serial.available())
  { 
    while(Serial.available())
    {
      mySerial.write(Serial.read());
    }
    mySerial.println();
  }
}

Set Baud and Enable Charging Function

It is recommended to execute this process when first time to use the module. In the Serial Monitor columns of following tables, input of AT commands are in back, module returns values are in orange.

Serial Monitor Description
AT
OK
Send command “AT” to synchronize baud rate. Serial port of module is by default set at auto-baud mode, and in this mode, it will not output any indications when the module is on.
AT+IPR=9600
OK
Set baud rate at 9600bps, supports baud rate from 1200bps to 115200bps.
AT+ECHARGE=1
OK
Send command “AT+ECHARGE=1” to enable battery charging function. By default the charging function is closed.
AT&W
OK
Save parameter setting.
AT+CPOWD=1
NORMAL POWER DOWN
Power down the module.
RDY
+CFUN: 1
GPS Ready
+CPIN: READY
Call Ready
SMS Ready
Turn on the module again by the power button, it will response status about GPS and GSM.
AT+CBC
+CBC: 1,96,4175
OK
Inquire charging status and remaining battery capacity.
AT+CSQ
+CSQ: 14,0
OK
Inquire GSM signal quality.

Get location with GPS

Serial Monitor Description
AT+CGPSPWR=1
OK
Open GPS
AT+CGPSSTATUS?
+CGPSSTATUS: Location Not Fix
OK
Read GPS fix status, “Location Not Fix” means that positioning is not successful. For the first time to start, it will take at least 30s. GPS must be tested by the window or outdoor.
AT+CGPSSTATUS?
+CGPSSTATUS: Location 3D Fix
OK
GPS has fixed with 3D status.
AT+CGPSINF=0
+CGPSINF:
0,2234.931817,11357.122485,
92.461185,20141031041141.000,
88,12,0.000000,0.000000
Get the current GPS location information. Parameters formate: <mode>, <altitude>, <longitude>, <UTC time>, <TTFF>, <num>, <speed>, <course>
AT+CGPSOUT=32
OK
$GPRMC,043326.000,A,
2234.9414,N,11357.1187,E,
0.000,143.69,311014,,,A*50
Read NMEA $GPRMC data, of which, “2234.9414 N, 11357.1187 E” is the location coordinates. For more details about NMEA sentences, check this site.
AT+CGPSRST=0
OK
Reset GPS in Cold Start Mode.
AT+CGPSRST=1
OK
Reset GPS in Hot Start Mode.
AT+CGPSPWR=0
OK
Close GPS.

Resource


Related Projects

It's a pity that we don't have any demo about LoNet-GSM/GPRS/GPS Breakout in the Recipe yet.

Post your awesome project about LoNet-GSM/GPRS/GPS Breakout to win $100 Coupon!. Please feel free to contact us: recipe@seeed.cc


Here we introduce some projects about GPRS Shield as a reference.

What is GPRS shield

Features:


SMS Remote Control



This project describes how to turn your hot water heater on and off via SMS and check if it is on or off.

It is reliable, secure, easy and flexible because of the reasons below:


I want to make it.

Arduino Phone



Arduino phone is a cell phone made by ourselves via combining Arduino and other shield modules.

This project tells us what you need to do when Arduino Phone apps can't fit your needs.

This Arduino Phone contains the following main functions.



I want to make it.

More Awesome Projects by GPRS


Share Your Awesome Projects with Us

Born with the spirit of making and sharing, that is what we believe makes a maker.

And only because of this, the open source community can be as prosperous as it is today.

It does not matter what you are and what you have made, hacker, maker, artist or engineers.

As long as you start sharing your works with others, you are being part of the open source community and you are making your contributions.

Now share your awesome projects with us on Recipe, and win a chance to become the Core User of Seeed.


Get more information about Core User, please email to: recipe@seeed.cc



Support

Any tech support, please contact support@deegou.com

Service

We do also provide PCB services ( Electronics design, prototype assembly and batch manufacturing ) If you have any requirements, please contact info@deegou.com

Copyright (c) 2008-2016 Seeed Development Limited (www.seeedstudio.com / www.seeed.cc)
This static html page was created from http://www.seeedstudio.com/wiki